StarTechcom 6U Wall Mount Network Rack - 14 Inch Deep (Low Profile) - 19" Patch Panel Bracket for Shallow Server and IT Equipment, Network Switches - 44lbs/20kg Weight Capacity, Black (WALLMOUNT6)

#1 recommendation - do NOT use the provided screws to attach this rack to the wall. Especially do not use such a light drywall anchor for a heavier item such as this. Fully loaded, this can weigh quite a bit. The picture attached shows a 1/4-1 inch screw that attaches the rack to a plywood panel. If you want a lasting installation, use a piece of plywood that is anchored to studs, then you can use heavy screws to attach - and use all four.Having said all that - there is a slight amount of flex on the back, I wish the screw holes had been placed more outboard (next to the sides) to prevent this. However, given the load I have on this I used the existing holes and they are fine.As other reviewers have noted, only 12 cage nuts are provided, which is usually just good for 3u worth of devices.Aside from the above, this is a nifty little rack and I am very pleased with it.

I bought this rack unit because I've started to get some new gear for my personal music/recording studio. I currently have an Avid Eleven Rack and a BBE 362 Sonic Maximizer as rack-mount effects.Let me say this unit is a beast and sturdy as a tank. As shown in the pics, it holds my rack FX perfectly with three additional spaces leftover (the 11 Rack uses 2 spaces all by itself) and still has plenty of room to hold my old Mac Mini and my Behringer audio interface (U-Phoria UMC204HD). The top is open, but I found a perfectly sized spare shelf I had to place my HD monitor on top of the whole setup.The rack unit comes with the stabilizer bar already assembled and everything ready to go. In the fairly large box it came in I received the rack unit, a one-page instruction manual in a plastic binder sleeve, and all the necessary accessories bubble-wrapped and zip-tied to the unit itself. Everything I needed, in other words—with plenty of space for cord management and airflow in the back of the unit.Included are enough rack screws, clip nuts, and washers to install 3 or 4 rack-mount effects. It would be nice if they also included enough for the rest of the unit's shelf space (6 rack FX in all), but it's definitely not a deal-breaker and not worth the removal of a star rating.If you're looking to get into rack-mounted FX for yourself, give this bad boy a try. You won't regret it.

Perfect for a home network - well priced, decently made, and took me to the "next level" with my home networking equipment. Easy to install and sturdy. There is a horizontal brace that can be top or bottom mounted depending on what you have installed, which will give the rack the proper squared up dimensions to install standard width network equipment in. Keep in mind that this rack has some flex in the vertical side panels which will disappear once a couple of items are installed in it.Check out "Budget Nerd"s YouTube channel for a nice little primer on this setup; Tom Lawrence also has a nice video on his "Lawrence Systems" YouTube channel called "DIY Home Rack Build" which goes over some great options for modular keystone patch panels.I installed this on a stud framed wall in my basement, a work in progress. I'll likely sheath the stud wall in plywood to give me flexibility to mount other networking equipment as needed.

I got this to fit a Ubiquiti layer 3 and it gave enough room behind the switch to manage plugs without bending. Added a central power source. If I continue to need more components for home use, I'll likely add another. This is sturdy, matches to 16" on center studs and went up quickly. I did move the stability bar to the underside as after adding my power, it needed to move, but outside of that, it wasn't anything I needed to remove my stuff out of, just the bar.

A sturdy rack that was easy to install and comes with accessories! If I could give it 4.99 stars I would. Almost perfect. Other reviewers complained about the screws and stabilizer bar. The included screws seemed a little short for going through sheetrock and then into wood. They did not go very far into the wood, but they held and would probably be OK for lightweight items. I happened to have longer 1 1/2 inch screws in my toolbox so I used those instead. The other weird thing about the screws is they are wood screws, the instructions say they are only to be used with wood, the holes are spaced for wood studs, but why were there are also some blue drywall anchors in the bag with the screws? The stabilizer bar does intrude into the top rack position. However, that's where I located my patch panel and the wire holder bar clears it - see picture - had no problems zip-tie-ing thick CAT 6A to it without removing the stabilizer bar.

Seems to be good quality. Hardware included, thankyou.Using it to set up an at home network.

Residential network where I pulled string out of the walls using a robust, antiquated phone line network, replaced with Cat6 throughout.This is definitely the right size rack for any home network that has or will eventually have wired ports, network storage and/or security cameras. Overkill if you're doing less than 6-10 network drops, or have a full pile of rack-able home theater equipment (might be too small in that case).As others have mentioned, the cross bar is mounted in a way that's convenient for the manufacturer to ship, but you SHOULD plan on flipping or reversing the cross bar to suit your needs. There are pre-drilled holes top and bottom of the unit, so mine is re-mounted upside down on the bottom of the rack, so as not to conflict with a rack power strip, and to free up space at the top for a rack shelf. I would agree with others, too, that say it's plenty robust without, once you have a few devices mounted. YMMV.