SUPAREE LED Fog Lights with Halo Ring White DRL/Yellow Turn Signal Fit for Tacoma 2005-2011/Tundra 2007-2013/Solara 2004-2006/Sequoia 2008-2015 Ideal for All-Weather Conditions,2 Pack

Supper bright lights for you vehicle. Fit just perfect in my Toyota Tacoma. These are water resistant and good quality made. Great price as well. Very impressive.

Overall the product looks good and fit perfectly…. I will share a few things to save you the headache’s I went through during this install. They are plug and play but when I plugged it in the “correct” way, nothing came on. When I flipped it around and plugged it in the “incorrect” way, the lights came on. I just added electrical tape to ensure it stayed secure. Next, if you plan on wiring the DRL’s and turn signal lights just know that you will need to splice into your DLR/TurnSignal wiring harness.Purple Wire = DLRRed Wire = Turn SignalThis information is not on the instructions and I did a lot of research to find that data. So good luck!! See photo of wire harness for reference.

Very simple install, lights a very bright and running lights are perfect in day light.

Installed these on my 2007 Tundra, they look and perform great!Things to know:1. For the 07 Tundra removing the old fog light was not described well. The retaining clips are on the right and left side and you can insert you hand and release one side and then the other. You will also have to release the retainer for the adjustment screw pressing in on the small clips. Once all three connecting points are free (as well as the wiring plug) the old fog light will slide out to the front.2. The + and - on the new fog light were reversed. You can resolve by turning the connector over and inserting, but there will not be a clip holding it in place. Wasted some time trying to figure out why they wouldn't turn on... The friction is holding fine but recommend electrical tape or a small zip tie.3. I needed additional wire and connectors to connect the orange and white halos. Not much but it was needed.4. Tap into the daytime running light positive wire, I used a volt meter to id the correct wire, and connect to the fog light blue wire.5. I chose to tap into the side marker positive wire, use a volt meter to id the correct wire, and connect to the green wire. You will need to remove the head light fixture to do this, be careful when removing the panel just below the head lights, it is easy to break the insertion pins. I did break them off on one side and used double sided 3M tape to secure when reinstalling, new panels are expensive. And yes the securing push pins will likely break as well so have some on hand. I have aftermarket head lights so the side marker was my best choice. If you can find another wire that provides 12v when the parking lights are turned on that would be a better option.6. The push clips for the wheel well cover that has to be removed will break on an older Tundra. Have spares on hand for when you reinstall.7. Check and adjust the fog light angles with the adjustment screw before installing the wheel well covers. It makes a big difference when they are adjusted correctly.With the wiring connection above the orange halos will be on whenever you only have DRLs (lights turned off) and they will blink in sync with your orange (also DRL) blinkers. This provides an all-orange DRL and blinker configuration during the daytime.When you turn on your parking lights, or head lights, the orange halos go off and the white ones turn on providing an all-white front lighting except when you use your turn signal. The halo will blink orange in sync with your current blinker.Hope this helps with your install.

Good looking lights but One of the light cases started getting moisture in it within a month, LEDS didn’t last long after that. Told them about the issue i had and they sent a replacement.With the way they handled the issue, it makes me think they’re a good company.I wouldn’t have a problem putting their lights on my next truck

The media could not be loaded. The lights look great in person. Decently bright also. My one issue is that they managed to get water in them and now the LEDs that were submerged are no longer working. The yellow and white LEDS were affected. If I had known this could be an issue, I would've taken extra steps to make sure they were waterproof. They're definitely not as bright as they used to be out of the box.3/5, I would be completely satisfied if the lights weren't affected by the water.

The media could not be loaded. easy to connect and fits perfectly, very good product.

They’re bright and I love the amber marker and turn lights, but worthless cause they are not at all water proof.

Pics speak for themselves. They matched my aftermarket headlights perfectly on the 2nd gen. Wired them into the turn signals with no issues but if you don't have any electrical work experience, i HIGHLY recommend you find a good friend that does or take it to the shop. You need to splice into existing cables and use a voltmeter to even figure out which cables you need to cut. I also used a lot of things from my electrical kit to ensure the connection will be reliable like shrinkwrap tubing and clips. The lights did not come with this little stuff that keeps the weather out.Used the lights for a few months now. No problems. Only criticism is that they don't fit 100% perfectly but it's so minor that I hesitate even saying it. There is also a minor delay in the white colour turning on when switching from DLR lights to headlights. Again, super duper minor. 5 stars all the way.