2 Port POE Extender Comply IEEE 802.3af/at Standard 10,100Mbps, POE Repeater 100 meters(328 ft) Extender 1 in 2 Out for POE IP Camera over Cat5/Cat6 or Better UTP Cables (POE5003)

Does what it says - splits single PoE to feed two cameras.Works well. Check the maximum watts available though to avoid over-heating.

Used this in a local community building to enable the daisy-chain connection of 2 or 3 PoE devices where it wasn't possible to install multiple individual network cables back to the main PoE switch. Nice small unit that tucks into a small space (used double sided padded tape) to conceal it.

Sometimes reviews are left for other products and then the listing changes. So to be clear, this is a review for the "Revotech Gigabit 2 Port POE Extender, IEEE 802.3af/at PoE+ Standard, 10,100,1000Mbps".I needed to replace a Unif UAC-Pro with a U6 LR. So I was about to lose an additional Ethernet port that I had connecting to a small switch by my PC. Using this extender, I am now able to power the extender with the original POE+ supply, connect and power the U6-LR and also power a small POE Flex mini switch. I can confirm that I am getting Gbe speeds and that there were no compatibility issues - everything just functioned straight away. I suspect that it might not be as smooth sailing for others, particularly if cameras are involved - however, it has suited my needs perfectly and I can't fault it.

I bought this to try out and with the hope of saving my self a alot of work running a second cable. It works well but does need some extra configuration on the cameras and recorder. As it did not work as plug and play first time.For me this method worked using a Hikvision NVR a 2 4K camerasPlug camera 1 in only and assign a static IP then remove cam 1 and plug in cam 2 and assign static ip. Then you can plug both cameras back in and goto recorder. Turn off plug and play and select manual adding. fill in the IP address for cams one and two on your chosen channels and both should be displayed. At first I didnt do this and the images on the recorder kept switching between the two cameras possibly due to an IP conflict.Also the device just about fits in a 100x100x50mm junction box. But is quite tight so would recommend a larger boxCannot say how reliable it is because I have only just fitted it

So good I bought two. Ideal in cases where peripherals such as CCTV cameras are too far from the recorder for good results. I used it between my Hikvision Recorder and Hikvision Camera. One thing that should be noted is that there are two main groups of POE. This device uses the full implementation (IEEE 802.3af) Mode A on pins 1/2 (+) and 3/4(-).Some "POE Cameras" use the more limited version using a fixed voltage (typically 24V) - often using a dedicated POE injector. This implementation is typically found using Pins 4,5+ and 7,8- of the RJ45 connector. This type of POE camera is NOT COMPATIBLE with this adaptor. Also remember that the single PORT has a maximum power output of 12.2W. I suspect that the two port version which is marginally larger is limited to about the SAME power split between the ports. Beware if trying to run two 6W cameras.

Ordered my first one that started smoking within the first 5 minutes of being plugged in. The second one didn’t even power up. The input was plugged in to a 802.3bt compatible switch and the output was plugged in to wireless access point that doesn’t draw anywhere near 30W.

Bought one of these devices in Sept 2021. Needed to run two 100Mpbs Hikvision PoE cameras over a single CAT6 cable. The device appears to have a three port switch within it (one input and two outputs). Worked perfectly, no issues. I found the unit to be small enough to just fit within a large Hikvision camera mounting box / back box.I estimate that the CAT6 cable run from the PoE switch was around 30-40M, the runs from the device to the cameras: 20cm and around 2M.Been working for around 2 weeks now without any issues.

Easy to install and worked well for a week then failed so have had to return.

Finally, I found a POE extender that actually supports my Reolink POE cameras. Now I can add four more POE cameras without buying a new NVR.

This 2 port PoE extender works great. I only had 1 cat5e wire drop to location the needed 2 PoE IP security cameras. This PoE extender allows me to power both cameras and receive both 4K video streams. Just plugged it in and it worked. Be mindful of the power requirement you need from each port.

Perfekt snabb leverans funkar bra 👍💯

Alles wie beschrieben. Danke

Via un injecteur POE de 30 w , on peut installer deux cameras en poe sur le meme cable d entree car deux sorties .l avantage pas besoin de courant a l endroit du repetiteur poe , je trouve un peut cher car vous devez acheter un injecteur poe de 30 w en plus, on arrive a trouver des switch 4 ports poe a moins de 30 euros